STEP TUTORIAL FOR BATHTUB INSTALLATION

Step Tutorial for Bathtub Installation

Step Tutorial for Bathtub Installation

Blog Article

Click Here

Every person maintains their own rationale on the subject of A Step-by-Step Guide to Installing a Bathtub.


How to Install a Bathtub
Setting up a tub isn't exactly rocket science, however it does require solid plumbing, woodworking, and occasionally, tiling skills. Replacing an old bath tub with a brand-new one is likewise a moderately challenging job. If the old bathtub is readily easily accessible, the task can relocate rapidly; if you have to open a wall surface to remove the old tub and also place the new bath tub, the task is much harder. In either case, the job is within a house handyman's skills, although you will certainly need an assistant to move out the old tub as well as embeded in the new one. Make sure you have qualified on your own for the task and also are comfortable trying it. As opposed to hiring a contractor to take control of a halfway-completed project, it is much better to take into consideration using one before you begin. Chances are you might require an expert plumber to make tube links.
This short article will aid you set up a brand-new bath tub in your washroom if you have currently acquired a new bathtub as well as do not require to alter the plan of your previous water pipelines.
Your tools and material checklist need to consist of the following:
  • New Bathtub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you require to replace old taps with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain any kind of water continuing to be in the system. The process of eliminating the existing faucets can be fairly troublesome because of the restricted gain access to that is often the situation.
    Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipes. Once the supply pipelines have been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the solitary taps from turning during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any old sealing substance.
    Before moving on to fit the new taps, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new faucets to fit.

    Fitting New Touches


    If the tails of the brand-new faucets are plastic, then you will require a plastic connector to stop damages to the thread. One end of the port fits on the plastic tail of the tap and also the various other end gives a connection to the current supply pipes.
    If you require to fit a monobloc, after that you will certainly need minimizing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
    Next, place the tap in the placing hole in the bath/basin making certain that the washers are in location between the faucet and also the sink. Safeguard the faucet in place with the producer provided backnut. As soon as the tap is firmly in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet ports. The previous kind should be linked to the tap finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been connected.

    Mounting the Bathtub


    Using the two wooden boards under its feet, put the bathtub in the required setting. The wooden boards are useful in evenly spreading the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small points.
    The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by examining the spirit level and adjusting the feet on the bathtub up until the spirit level reads level.
    To mount taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipe by making a compression join; after that do the exact same for the other faucet.
    Turn on the water and examine all joints as well as new pipework for leaks as well as tighten them if required. Load the tub and additionally examine the overflow electrical outlet as well as the normal electrical outlet for leaks.
    Ultimately, take care of the bath paneling as explained in the producer's user's manual. Tiling and also securing around the bathtub must wait until the tub has been utilized a minimum of once as this will settle it into its last setting.

    Planning for the Installment


    To start with, the sustaining frame provided with the bath should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bathroom and also the taps. On a plastic bathroom, it is likewise sensible to fit a supporting plate under the taps device to stop strain on the bathtub.
    Fit the versatile tap ports to the bottom of both faucets making use of 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the supplied washers.
    Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a similar manner.The bath should now prepare to be fitted in its final position.

    Tiling Around the Bathtub


    In the location where the bath satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate sufficient to fracture a stiff seal, triggering the water to permeate the wall in between the bath as well as the tiling, resulting in complications with dampness and also possible leaks to the ceiling below.
    You can choose from a selection of coloured sealants to assimilate your fixtures and also fittings. They are marketed in tubes as well as cartridges, as well as are capable of sealing voids up to a width of 3mm (1/8 inch). If you have a larger void to fill, you can fill it with spins of drenched paper or soft rope. Remember to constantly fill the bathtub with water prior to securing, to permit the movement experienced when the tub is in use. The sealer can fracture rather early if you do not take into consideration this motion prior to sealing.
    Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently available on the market. It is advisable to fit the floor tiles making use of waterproof or waterproof sticky and also grout.

    How to Install or Replace a Bathtub


    Find Your Dimensions


    The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.



    After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?


    Disconnect the Water Supply and Drain Assembly


    Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.



    Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.



    Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.


    Cut Out the Old Tub


    After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.



    Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.



    Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.


    Install the New Tub


    Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.



    Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.



    Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.



    When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.


    Secure the Tub


    After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.



    Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.



    Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.



    Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

    https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/


    Tools You Need to Install a New Bathtub

    As an avid reader on Tools You Need to Install a New Bathtub , I imagined sharing that blog post was valuable. Don't hesitate to set aside a second to share this article if you liked it. I cherish reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.


    Visit Our Site

    Report this page